Laptop charging port repair & replacement in Orlando & Central Florida
A laptop that only charges at an angle, or not at all, usually has cracked solder joints, a worn jack or a damaged USB-C port. We test the charger and battery first, then repair or replace the port, whether it’s soldered to the motherboard or on a cable, and charge-test it before you get it back.
5.0 on Google · 33 reviews
On-site or in our shop, by appointment.
What’s included
- Laptop Charging Port Repair & Replacement
- Charging Port Soldering
- Where
- Your home, office or our shop
- Booking
- By appointment
- Hours
- Mon–Sat, 9 AM–9 PM
- Covers
- 31 Central Florida communities
Sound familiar?
Tick what matches. It goes straight into your request, so you don’t type it twice.
How we handle it
The same four steps every time, so you always know what’s next.
- 1
Rule out the charger
We measure your adapter’s output, check the cable and tip for breaks, and read the battery’s health. A worn charger or battery should never be mistaken for a broken port.
- 2
Open and inspect
Under magnification we look for cracked joints, lifted pads, scorch marks and worn contacts. We also confirm whether your jack is soldered to the board or mounted on a cable.
- 3
Repair or replace
A jack on a cable harness is swapped out. A board-mounted jack or USB-C port is desoldered and replaced, damaged pads are rebuilt, and cracked joints on a sound jack are reflowed.
- 4
Charge-test it
We charge from a low battery with your own adapter, gently flex the plug, and confirm Windows reports it charging. We also check that nothing near the port runs hot.
Barrel jack or USB-C: two different repairs
A barrel DC jack takes a round plug and comes in two designs. Some sit on a short cable harness that plugs into the motherboard and is held by a bracket, so replacing one takes no soldering. Others are soldered straight to the motherboard: the old jack is desoldered, the holes are cleaned, a new jack goes in, and any torn pads are rebuilt.
A USB-C Power Delivery port is a small surface-mount part with 24 contacts. Before power flows, the charger and laptop negotiate a voltage, up to 20 V on most laptops. Damage to the pins or chip that handle that negotiation can leave a port that charges only with the plug one way up, or only at a trickle. Replacing it takes hot-air rework and micro-soldering, though on some models the port sits on a small daughterboard that simply swaps out.
Why wiggling the plug makes it worse
Finding the angle that makes it charge feels like a fix. It isn’t. Each wiggle flexes solder joints that have already cracked, and every time the contact makes and breaks under load, it sparks on a tiny scale. That arcing pits and burns the contacts and can scorch the board around them.
Given time, a pad lifts or a trace tears, and a routine jack replacement becomes a board repair. Propping the cord on a book or taping it in place does the same damage, only slower. If your laptop only charges at one angle, stop using the trick and have the port looked at while it is still a simple repair.
Sometimes it isn’t the port
Before we touch the port, we rule out the parts around it. A failing adapter can put out the wrong voltage or none at all. Most Dell and HP adapters should read about 19.5 V, and many Lenovo adapters 20 V. Dell and HP plugs also have a thin center pin that tells the laptop which adapter it is. If that pin or its wire breaks, the laptop may refuse to charge or warn that the adapter type can’t be determined.
A worn battery can look like a port problem too, and a Windows battery report shows its remaining capacity against the original. Some faults sit deeper, in the charging circuit on the motherboard. We’ll show you what we find, and if a board repair isn’t worth it on an older laptop, we’ll say so.
Questions about charging port repair
Still unsure? Call or text (407) 773-0904 and describe what’s happening.
How do I know if it’s the charger or the charging port?
Try a known-good charger made for your laptop: if it charges normally, the old charger was the problem. If the plug still feels loose or only charges at an angle, it’s the port, and we confirm either way before recommending a repair.
Can a loose charging port be fixed without replacing it?
Sometimes. If the jack itself is sound and only its solder joints have cracked, reflowing them with fresh solder restores a solid connection. If the contacts inside are worn or burnt, the jack needs replacing.
Can you repair a USB-C charging port?
Yes. USB-C ports are surface-mounted with tiny contacts, so the work is done in our shop with hot-air rework and micro-soldering. On some models the port sits on a small daughterboard, which makes it a simpler swap.
Is it safe to keep using a laptop with a loose charging port?
It’s best not to. Intermittent contact causes tiny sparks that burn the contacts and can damage the board around them, turning a routine jack repair into a harder one.
On-site across Central Florida
We handle charging port repair at homes and offices in 31 communities, by appointment.
Request this service
Two short steps. We’ll call or text you during business hours to set a time.
- We read it. Your request goes straight to our inbox.
- We reach out. By call, text or email, Mon–Sat 9 AM–9 PM.
- We fix it. At your home or office, or in our shop for bigger jobs.